Search Results

A large eddy simulation approach and different breakup models are used to analyze fuel injection and atomization processes in a constant volume combustion bomb. The study is focused on the influences of the subgrid turbulent kinetic energy, especially the source term induced by the fuel spray, on the droplet movement and spray characteristics. Furthermore, the influence of different subgrid scale (SGS) models, including the constant coefficient and dynamic Smagorinsky models, WALE model and the K-equation turbulent energy transport model, on fuel sprays and the turbulent dispersion of droplets are examined. Factors affecting the fuel spray are discussed based on numerical computations for various operating conditions and are compared with experimental data.

Fuel properties are always considered as one of the main factors to diesel engines concerning performance and emission discussions. There are still challenges for researchers to identify the most correlating and non-correlating fuel properties and their effects on engine behavior. Statistical analyses have been applied in this study to derive the most un-correlating properties. In parallel, sensitivity analysis was performed for the fuel properties as well as to the emission and performance of the engine. On one hand, two different analyses were implemented; one with consideration of both, non-aromatic and aromatic fuels, and the other were performed separately for each individual fuel group. The results offer a different influence on each type of analysis. Finally, by considering both methods, most common correlating and non-correlating properties have been derived.

Tightening of emission norms necessitate intensified research in the field of emissions reduction. Fuel research opens up a vast area of potential improvement, since combustion behavior and the nature of the combustion products can be heavily influenced by fuel composition. In this paper, the effects of fuel properties on combustion and emissions shall be discussed, based on the study of standard diesel fuel, two types of diesel-like fuels and a kerosene fuel. Investigations were conducted on a single cylinder heavy duty direct-injected diesel engine operating under part-homogeneous combustion in the part-load operating range. For this purpose, a statistical design of experiments method (DOE) was utilized in order to evaluate the influence of each fuel property and, thus, develop a model for all selected fuels. Variation in EGR rates, injection and air patterns have significant effects on the combustion in the fuels under investigation.

The requirement of reducing worldwide CO₂ emissions and engine pollutants are demanding an increased use of bio-fuels. Ethanol with its established production technology can contribute to this goal. However, due to its resistive auto-ignition behavior the use of ethanol-based fuels is limited to the spark-ignited gasoline combustion process. For application to the compression-ignited diesel combustion process advanced ignition systems are required. In general, ethanol offers a significant potential to improve the soot emission behavior of the diesel engine due to its oxygen content and its enhanced evaporation behavior. In this contribution the ignition behavior of ethanol and mixtures with high ethanol content is investigated in combination with advanced ignition systems with ceramic glow-plugs under diesel engine relevant thermodynamic conditions in a high pressure and temperature vessel.

The development of electromechanical actuators (EMAs) is the key technology to build an all-electric aircraft. One of the greatest hurdles to replacing all hydraulic actuators on an aircraft with EMAs is the acquisition, transport and rejection of waste heat generated within the EMAs. The absence of hydraulic fluids removes an attractive and effective means of acquiring and transporting the heat. To address thermal management under limited cooling options, accurate spatial and temporal information on heat generation must be obtained and carefully monitored. In military aircraft, the heat loads of EMAs are highly transient and localized. Consequently, a FEA-based thermal model should have high spatial and temporal resolution. This requires tremendous calculation resources if a whole flight mission simulation is needed. A lumped node thermal network is therefore needed which can correctly identify the hot spot locations and can perform the calculations in a much shorter time.

The finite nature and instability of fossil fuel supply has led to an increasing and enduring investigation demand of alternative and regenerative fuels. An investigation program is carried out to explore the potential of tailor made fuels to reduce engine-out emissions while maintaining engine efficiency and an acceptable noise level. In this paper, fundamental results of the Diesel engine relevant combustion are presented. To enable optimum engine performance a range of different reference fuels have been investigated. The fundamental effects of different physical and chemical properties on emission formation and engine performance are investigated using a thermodynamic diesel single cylinder research engine and an optically-accessible combustion vessel. Depending on the chain length and molecular structure, fuel compounds vary in cetane number, boiling temperature etc. Therefore, different hydrocarbons including n-heptane, n-dodecane, and l-decanol were investigated.

Within the Cluster of Excellence “Tailor-Made Fuels from Biomass” at RWTH Aachen University, the Institute for Combustion Engines carried out an investigation program to explore the potential of future biofuel components in Diesel blends. In this paper, thermodynamic single cylinder engine results of today's and future biofuel components are presented with respect to their engine-out emissions and engine efficiency. The investigations were divided into two phases: In the first phase, investigations were performed with rapeseed oil methyl ester (B100) and an Ethanol-Gasoline blend (E85). In order to analyze the impact of different fuel blends, mixtures with 10 vol-% of B100 or E85 and 90 vol-% of standardized EN590 Diesel were investigated. Due to the low cetane number of E85, it cannot be used purely in a Diesel engine.

A reduced kinetic reaction mechanism for the autoignition of dimethyl ether is presented in this paper. Dimethyl ether has proven to be one of the most attractive alternatives to traditional fossil fuels for compression ignition engines. It can either be produced from biomass or from fossil oil. For dimethyl ether, Fischer et al. (Int. J.Chem. Kinet. 32 ( 12 ) (2000) 713-740) proposed a detailed reaction mechanism consisting of 79 species and 351 elementary reactions. In the present work, this detailed mechanism is systematically reduced to 31 species and 49 reactions. The reduced mechanism is discussed in detail with special emphasis on the high temperature thermal decomposition of dimethyl ether and on the fuel specific depleting reactions, which produce the methoxymethyl radical. In addition, a reaction pathway analysis for low temperature combustion is applied, where hydroperoxy-methylformate is found to be the dominating parameter for the low temperature regime.

The fulfillment of the aggravated demands on future small-size High-Speed Direct Injection (HSDI) Diesel engines requires next to the optimization of the injection system and the combustion chamber also the generation of an optimal in-cylinder swirl charge motion. To evaluate different port concepts for modern HSDI Diesel engines, usually quantities as the in-cylinder swirl ratio and the flow coefficient are determined, which are measured on a steady-state flow test bench. It has been shown that different valve lift strategies nominally lead to similar swirl levels. However, significant differences in combustion behavior and engine-out emissions give rise to the assumption that local differences in the in-cylinder flow structure caused by different valve lift strategies have noticeable impact. In this study an additional criterion, the homogeneity of the swirl flow, is introduced and a new approach for a quantitative assessment of swirl flow pattern is presented.

The technology used in hybrid vehicle concepts is significantly different from conventional vehicle technology with consequences also for the noise and vibration behavior. In conventional vehicles, certain noise phenomena are masked by the engine noise. In situations where the combustion engine is turned off in hybrid vehicle concepts, these noise components can become dominant and annoying. In hybrid concepts, the driving condition is often decoupled from the operation state of the combustion engine, which leads to unusual and unexpected acoustical behavior. New acoustic phenomena such as magnetic noise due to recuperation occur, caused by new components and driving conditions. The analysis of this recuperation noise by means of interior noise simulation shows, that it is not only induced by the powertrain radiation but also by the noise path via the powertrain mounts. The additional degrees of freedom of the hybrid drive train can also be used to improve the vibrational behavior.

Today's biofuels require large amounts of energy in the production process for the conversion from biomass into fuels with conventional properties. To reduce the amounts of energy needed, future fuels derived from biomass will have a molecular structure which is more similar to the respective feedstock. Butyl levulinate can be gained easily from levulinic acid which is produced by acid hydrolysis of cellulose. Thus, the Institute for Combustion Engines at RWTH Aachen University carried out a fuel investigation program to explore the potential of this biofuel compound, as a candidate for future compression ignition engines to reduce engine-out emissions while maintaining engine efficiency and an acceptable noise level. Previous investigations identified most desirable fuel properties like a reduced cetane number, an increased amount of oxygen content and a low boiling temperature for compression ignition engine conditions.

In internal combustion engines operating in Controlled Auto Ignition (CAI) mode, combustion phasing and heat-release rate is controlled by stratification of fuel, fresh air, and hot internally recirculated exhaust gases. Based on the Representative Interactive Flamelet (RIF) model, a two-dimensional flamelet approach is developed. As independent parameters, firstly the fuel mixture fraction and secondly the mixture fraction of internally recirculated exhaust gases are considered. The flamelet equations are derived from the transport equations for species mass fraction and total enthalpy, employing an asymptotic analysis. A subsequent coordinate transformation leads to the phase space formulation of the two-dimensional flamelet equations. By the use of detailed chemical reaction mechanisms, the effects of dilution, temperature, and chemical species composition due to the internally recirculated exhaust gases are represented.

The purpose of this study is to investigate the effect of spray-bowl interaction on combustion, and pollutants formation at one specific high-load point of a single-cylinder small-bore diesel engine through computational analysis. The simulations are performed using Representative Interactive Flamelet (RIF) model with detailed chemical kinetics. Detailed chemistry-based soot model is used for the prediction of soot emissions. The simulations are performed for five different injection timings. Model-predicted cylinder pressure and exhaust emissions are validated against the measured data for all the injection timings. A new method - Two-part analysis - is then applied to investigate the spray-bowl interaction. Two-part analysis splits the volume of the combustion chamber into two, namely the piston bowl and the squish volume. Through analysis, among others the histories of soot, carbon monoxide (CO) and nitric oxide (NO ) emissions inside both volumes are shown.

Fuels derived from biomass will most likely contain oxygen due to the high amount of hydrogen needed to remove oxygen in the production process. Today, alcohol fuels (e. g. ethanol) are well understood for spark ignition engines. The Institute for Combustion Engines at RWTH Aachen University carried out a fuel investigation program to explore the potential of alcohol fuels as candidates for future compression ignition engines to reduce engine-out emissions while maintaining engine efficiency and an acceptable noise level. The soot formation and oxidation process when using alcohol fuels in diesel engines is not yet sufficiently understood. Depending on the chain length, alcohol fuels vary in cetane number and boiling temperature. Decanol possesses a diesel-like cetane number and a boiling point in the range of the diesel boiling curve. Thus, decanol was selected as an alcohol representative to investigate the influence of the oxygen content of an alcohol on the combustion performance.

The presented paper deals with the set-up and performance of a newly developed control system as well as with achieved engine results. This control system is able to control the entire cylinder pressure trace by using a flexible rate shaping injector and iterative learning control (ILC). Standard thermodynamic cycles, like isobaric and Seiliger cycles, and a newly suggested class of cycles are generated and analyzed on a single cylinder engine. With this control system an extremely flexible tool for optimization of combustion processes is available to exploit the full potential of injection rate- shaping on diesel engines.

In this paper a new approach is presented to evaluate the combustion behaviour of homogeneous gasoline engines by predicting burn delay and -duration in a way which can be obtained under the time constraints of the development process. This is accomplished by means of pure in-cylinder flow simulations without a classical combustion model. The burn delay model is based on the local distribution of the turbulent flow near the spark plug. It features also a methodology to compare different designs regarding combustion stability. The correlation for burn duration uses a turbulent characteristic number that is obtained from the turbulent flow in the combustion chamber together with a model for the turbulent burning velocity. The results show good agreement with the combustion process of the analyzed engines.

Within a public founded project test cell investigations were undertaken to identify parameters which predominantly influence the development of critical deposits in injection nozzles. A medium-duty diesel engine was operated in two different coking cycles with a zinc-free lubricant. One of the cycles is dominated by rated power, while the second includes a wide area of the operation range. During the experiments the temperatures at the nozzle tip, the geometries of the nozzle orifice and fuel properties were varied. For a detailed analysis of the deposits methods of electron microscopy were deployed. In the course of the project optical access to all areas in the nozzle was achieved. The experiments were evaluated by means of the monitoring of power output and fuel flow at rated power. The usage of a SEM (scanning electron microscope) and a TEM (transmission electron microscope) revealed images of the deposits with a magnification of up to 160 000.

So far, the effect of injection rate shaping on the diesel combustion in small-bore DI diesel engines has not been extensively investigated, especially at high part load conditions with high EGR rates. The benefit of injection rate shaping is already verified for heavy duty engines at high load conditions with and without EGR. For this investigation, single cylinder engine investigations were conducted at the VKA / RWTH Aachen University. In order to meet the future NOx legislation limits like US-Tier2Bin5 it is crucial to reduce NOx especially at the high load points of the certification cycles, as FTP75 or US06. For the single cylinder investigations two part load points were chosen, which have relevance for the mentioned certification cycles. The experimental work focuses on different rate shapes as rectangular (Common-Rail type), ramp and boot shape at high EGR rates.

The high-speed Dl-diesel engine has made a significant advance since the beginning of the 90's in the Western European passenger car market. Apart from the traditional advantage in fuel economy, further factors contributing to this success have been significantly improved performance and power density, as well as the permanent progress made in acoustics and comfort. In addition to the efforts to improve efficiency of automotive powertrains, the requirement for cleaner air increases through the continuous worldwide restriction of emissions by legislative regulations for diesel engines. Against the backdrop of global climate change, significant reduction of CO2 is observed. Hence, for the future, engine and vehicle concepts are needed, that, while maintaining the well-established attractive market attributes, compare more favorably with regard to fuel consumption.

Regulated emissions, CO2-values, comfort, good driveability, high reliability and costs, this is the main frame for all future powertrain developments. In this frame, the diesel powertrain, not only for passenger cars, but also for commercial vehicle applications, faces some challenges in order to fulfil the future European and current US emission legislations while keeping the fuel consumption benefit, good driveability and an acceptable cost frame. One of these challenges is the varying fuel qualities of diesel fuel in different countries including different cetane number, volatility, sulphur content and different molecular composition. In addition to that in the future, more and more alternative fuels with various fuel qualities and properties will be launched into the market for economical and environmental reasons. At present, the control algorithms of the injection system applied in most diesel engines is open loop control.